Water level switch location

images water level switch location

To test the switch for continuity, use a multimeter also called a volt-ohm meter set at OHMS x 1. If you desire a customized water level switch or sensor for your application, we can have it built for you within 72 hours. At FPI Sensors, we offer a wide range of accurate and dependable water level sensors that detect the level of water for various applications. Correct any problems by straightening or replacing the tube. With the use of your screwdriver, back out the screws that are holding the switch in place. Test them for continuity in pairs.

  • How to Replace a Washing Machine Water Level Switch
  • How to Test a Washing Machine Water Level Switch
  • Washing Machine Water Level Switches Dey Appliance Parts
  • How to Replace the Water Level Switch on a GE Profile Top Load Washer Home Guides SF Gate

  • Your washing machine has some internal switches that control various functions, and any one of them may go bad and require replacement. A faulty water level or pressure switch is one such device.

    How to Replace a Washing Machine Water Level Switch

    The water level switch sends power from the timer control to the water inlet valve and. The washing machine water level switch is located in your washer's control panel. Usually, the water level switch is next to the temperature control button. Products 1 - 20 of 49 Buy Washing Machine Water Level Switche at Dey Distributing.
    Push the tube onto the switch. Reconnect the tube to the switch in preparation for the second round of continuity testing.

    images water level switch location

    Do you need a reliable sensor or switch to help detect the water levels in your application? You should hear the switch click when you blow into the tube.

    The Spruce uses cookies to provide you with a great user experience. Remove the two screws from the brackets on each side of the washer cabinet. Inspect the water level tube and, if necessary, clear any blockage before testing the switch for electrical failure.

    images water level switch location

    images water level switch location
    Water level switch location
    Use the screws you removed previously to secure the trim and back panel.

    Check the hose attached to the washing machine water level switch and make sure that it is firmly in place. Usually, the washing machine water level switch has three connectors and the wires are color coded so it is easy for you to reconnect them later on. Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.

    There is no need for you to switch on your washing machine while you test the switch. Reverse your steps to reassemble the GE Profile washer. After removing the screws, grasp the switch in your hand and slowly pull it upward.

    Buy Whirlpool W Water Level Switch Kit: Parts & Accessories - Amazon .com ✓ FREE DELIVERY possible on eligible purchases.

    How to Test a Washing Machine Water Level Switch

    Buy Whirlpool W Water Level Switch: Washer Parts & Accessories - ✓ FREE DELIVERY possible on eligible purchases. The level switch also ensures the water in the washtub covers the entire load Note the locations of the wire connectors on the control board inside the panel.
    A water level temperature sensor will monitor both the level of the liquid and the temperature.

    Analyze the results of the second round of testing, and compare them to those of the first round. Remove the torx-head screws from the back of the control panel using a T torx-head screwdriver.

    images water level switch location

    Note the locations of the wire connectors on the control board inside the panel. After removing the screws, grasp the switch in your hand and slowly pull it upward. Pull the tube from the side of the switch. It should be firmly connected to fittings at each end.

    images water level switch location
    Water level switch location
    Just make sure that the hose is properly attached to the switch and things will be fine.

    Washing Machine Water Level Switches Dey Appliance Parts

    Grab the wire harnesses on top of the switch, and pull them off the top of the switch. Usually, the water level switch is next to the temperature control button. Plug the wire harnesses into the top of the switch. With the use of your screwdriver, back out the screws that are holding the switch in place.

    You can distinguish the water level switch from other round switches inside the washer cabinet by its rubber tube that runs from the switch down the side of the tub. The switch should turn on when the water in the washer reaches a certain level.


    Common types of temperature switches that can be combined for these applications include thermistors, thermocouples and resistance temperature detectors RTDs.

    Video: Water level switch location Washer Water Level Pressure Switch (part #DC96-01703C)-How To Replace

    As the washer fills, water enters the tube from the bottom and increases pressure in the airspace within the tube.

    Depending on the need, it can be configured to perform a variety of functions for different situations.

    If you desire a customized water level switch or sensor for your application, we can have it built for you within 72 hours.

    How to Replace the Water Level Switch on a GE Profile Top Load Washer Home Guides SF Gate

    Inspect the disconnected tube at each end for debris, sediment, and water. Usually, the water level switch is next to the temperature control button.

    images water level switch location
    RCH200 HOSE REEL
    Test them for continuity in pairs.

    Lift the brace, and squeeze the sides of the switch bracket holding it to the brace. Analyze the results of the second round of testing, and compare them to those of the first round. Some types of water level switches are attached to the washer through electrical wires, while others are simply lodged into sockets. Check the hose attached to the washing machine water level switch and make sure that it is firmly in place.

    4 Replies to “Water level switch location”

    1. Find the horizontal seam along the top front of the washer separating the top of the washer cabinet from the front panel. Disconnect them from the terminals: this usually means disengaging a plug, but if the wires are connected to the terminals by other means, label them for position before disconnecting them.

    2. We are so confident with our products that we warrant all of our products to be free from defects and workmanship under normal use for one full year from shipping date. As the washer fills, water enters the tube from the bottom and increases pressure in the airspace within the tube.

    3. As the tub fills, the switch cuts off the water flow when the water level inside the tub correlates with the setting for a large, regular, or small load. It could be dependent upon liquid level, pressure, flow or temperature.